Nail hair

ATTACHMENT OF NAIL HAIR

Straighten your hair. Use a protective plate and take out a thin strand of your own hair. Place the nail hair loop underneath and heat with a keratin wax heating tongs. When the wax has hit, you roll up the attachment with your own hair and press it together firmly. Make sure that the wax surrounds the entire strand of hair and that there is no air inside the attachment. Repeat the procedure loop by loop, leg by leg. Start at the neck and work your way up.

REMOVING NAIL HAIR

Apply remover to the mount and let it work. Use the remover pliers and squeeze the bracket firmly. Then you carefully pull or comb out the nail hair loop. Repeat the procedure on any leftovers. 

Tape hair

ATTACHMENT OF TAPE HAIR

Wash your hair with shampoo only (no conditioner or oil) and dry your hair completely. Bone up your hair. Remove the protective plastic from one loop and place it up against the lower edge of the leg. Lift up the loop and remove hair that does not follow. Place another strand of tape hair underneath the first so they meet tape to tape with your own hair in between. Press firmly, preferably with pliers, so that the tapes adhere firmly to each other. Repeat along the legs and then continue along a new leg until you are happy with the amount of extensions.

When attaching tape hair, be careful not to touch the tape with your fingers after removing the protective plastic. Also remember not to put the loops too close to the scalp and take as little of your own hair as possible between the tape loops.

TAPE HAIR REMOVAL

Apply remover over the entire mount and massage it in. Separate the strands with your fingers or with the help of a comb. Use more remover if necessary and then remove the tape loop. Apply remover to any residue. Repeat the procedure on each loop.

Tape hair fits very well if attached correctly, but it is required that you use the correct method of attachment. It is very important that you put as little hair as possible between the loops and that you press the tape firmly. If the tape doesn't stick, try putting two loops together without hair in between. If the tape sticks then there is nothing wrong with it and it should stick well if it is inserted correctly. It is also important to be careful when untangling your hair, especially if your hair is wet.

Ring hair (loop hair)

FIXING OF RING HAIR

To attach ring hair you need pliers and preferably a pin comb. Part your hair and take out a small strand of your own hair with the help of the comb. Pull the loop of your own hair through the loop of the ring hair loop. Then pull the loop through the microring and make sure that the microring ends up approx. 1 cm from the scalp. Use the pliers to pinch the microring. The microring should be squeezed tightly so that it is flat.

When attaching loop hair, remember to take the right amount of your own hair through the micro ring. You should feel a certain resistance when you pull the hair through the micro ring. If you take too little or too much hair, the micro ring will not attach properly.

REMOVING RING HAIR

Use the pliers and squeeze the microring in the opposite direction so that it opens. Pull the ring hair loop out of the hair and repeat on the remaining loops.

Nano hair

FIXATION OF NANO HAIR

Start by detangling your hair. Thread a couple of nano rings onto the hair hook. Take a strand of your own hair using a pin comb and pull the hair through the hook. Then pull the hair through the nano ring. Place a nano hair loop in the nano ring and pinch the nano ring together using a pair of pliers. Be sure to squeeze the nanoring tightly.

REMOVING NANO HAIR

Using the pliers, squeeze the nanoring in the opposite direction so that it opens. Pull the nano hair loop out of the hair and repeat the procedure on the remaining loops.

Hair bridle

With a hair bridle, the possibilities are many. You can sew your hairband or fasten it using micro rings. By sewing in clips, you can also create your own clip-on set. With a little effort, you can get a hair extension that is specially designed for you.

ATTACHMENT OF HAIR BAND

Clips: You need clips, needle (Unfortunately we do not sell) and wire. Cut the hair band into pieces, as long as you want them. Sew in clips with 5-10 cm intervals. You need approximately 20 clips for a clip-on set. Then attach it according to the clip-on instructions.

Weave: Straighten your hair. Make a baked braid horizontally along the legs and secure it. Cut a desired length of hair band. Thread thread onto a bent needle and sew the hairband into the braid. Repeat the procedure until you are satisfied with the amount of hair. Start at the neck and work your way up.

Microringar: Part the hair where you want to attach the loose hair and cut the length you want from the hair band. Thread a microring on a hook for microrings. Place the hair band against the underside of the legs. Use the hook to take part of your own hair and part of the hair band. Thread the hair through the microring and clamp the microring using a pair of pliers.

Ponytail

ATTACHMENT OF CLIP-ON PONY TAIL

Make a ponytail in your own hair. Attach the comb to the ponytail and then tie the velcro around. Secure the end of the hair with a bobby pin.

CLIP-ON PONY TAIL REMOVAL

Unfasten the velcro and lift the ponytail away.

Clip-on

ATTACHMENT OF CLIP-ON

Comb the hair at the back of the head. You can tuft your own hair at the bottom of the legs so that the clips stick better. Open the clips on the clip-on part, hook them into the toupee and press the clips to close. Then continue in the same way with the other parts. Start at the neck and work your way up and then to the sides. 

REMOVING CLIP-ON

Open the clips and remove the hair section by section.

Halo extensions

ATTACHMENT OF HALO EXTENSIONS

Place the thread over your own hair, a few fingers' width from the hairline on the forehead. Press your halo hairpiece down so that it is secured over your own hair, making sure the clips are open. Press the clips so that they close and sit in your hair. The thread is adjustable so that it fits you. When the extension is in place, take a pin comb and pull up your own hair so that most of it ends up above the wire and the extension so that it is hidden.

REMOVING HALO EXTENSIONS

The clips are opened and then the wig is simply lifted upwards and comes off the head.